Gianni Industries DG-15 Series Manuel d'utilisateur télécharger pdf

DG-15 series Digital Keypad Entry system

Operation User's Manual

1. Specifications:

 Operating Voltage: 12 Vdc

 Current Draw: Average 15mA, Peak 100mA @ 12Vdc

 Input: request-to-exit, time out reed switch contact

 Output: Dual relays, N.O./N.C./Com. Output (free voltage

contact)

 Relays Electric Current: 2A MAX @30Vdc ；0.4A @

120Vac

 Relay Activation Time:

 Relay 1 time delay setting code「＊30」、Relay 2

setting code「＊31」

 Strike Time: 1~99 seconds（adjustable）

 Strike mode: Access Timer or Latch

 Memory Volume: 20+1 PIN codes

 Relay 1 is controlled by ＊01~＊20 user slots

 Relay 2 is controlled by ＊21 user slots

 Operating Temperature: -20~+70℃

 Ambient Humidity: 5~95% relative humidity non-condensing

 Factory Master Code: 12345

 Invalid PIN Lock-out: The system will shut down for 60 seconds while 30 codes of

incorrectly Master Codes enrolled or PIN codes attempted（None beeper signal of

keypad activations）.

 EPROM: Non-volatile memory, System will retain all programs and codes after a total

loss of power.

 The indicator signal chart:

LED signal Sound signal

Green LED Power on, stand-by 1 Beep

Effective PIN codes、Any key pressed

Red LED Relay 1 activated 2 Beeps

Entering 、Exiting from the Program mode

Yellow LED Relay 2 activated 3 Beeps Data computing error

5 Beeps

Master Code reset to Factory （12345）

2. Operation Instruction:

 Enter Program Mode:

1. Compose twice the master code (4 digit format press「1234」、5 digit format press

「12345」) → 2 beeps → you are now in the "programming mode".

2. After 60 seconds if you have not entered any codes or data, the system will

automatically exit from the programming mode.

 Exiting from the program mode:

1. Press「#」 to exit from the programming mode.

2. After 30 wrong codes attempts at the master code the lockout facility will operate.

 Add PIN codes

Enter the Programming mode, Enter the slot position code 「＊01~＊20」→????? Input

5 digit （or 4 digit）PIN codes→ (beep) enrolled Æ（repeat）

Press 「#」 to exit from the programming mode, or program other operating.

Note 1: The codes「0000」,「00000」,「1234」,「12345」or master code are not be

used for PIN code.

Note 2: Relay 2 is controlled by ＊21 user slots

 To Delete a User Code：

P-MU-DG15 Ver. C Publish:2008.11.12 Page: 1/ 3

1 2 3

Résumé du contenu

Page 1 - Operation User's Manual

DG-15 series Digital Keypad Entry system Operation User's Manual

Page 2 - is moved

Enter the Programming mode→ Press the slot position code of your choice to delete (example "06") →Press「＊06」→「0000」（or「00000」）→（be

Page 3

Note:  The suggested wire gauge is #22~26 AWG.  The varistor or diode must be connected across the lock terminal (electromagnet...) operated by t

Commentaires sur ces manuels

Pas de commentaire

Gianni Industries DG-15 Series Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Claviers numériques Gianni Industries DG-15 Series. Gianni Industries DG-15 Series User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Claviers numériques Gianni Industries DG-15 Series